you going to have it at the Roadster show this year?
Announcement
Collapse
No announcement yet.
Project Austin street gasser.
Collapse
X
-
Originally posted by SuperBuickGuy View Postyou going to have it at the Roadster show this year?
Had the Austin out for it's first run since the engine and bodywork, and a friend wanted me to take him for a spin so he could video it. Should have warmed it up first, as it's really cold blooded with no choke, but here's a link to the video:
Comment
-
The Harwood buckets have proven to not be good for much more than 1/4 mile drives! Very uncomfortable after an hour drive, and probably because of the 1/2" padding. I liked the look, but since I plan to drive it a lot they have to go.
I'm going with CJ5 seats, as they're very narrow and at 19" wide will fit my narrow 42" cab.
Comment
-
Spent the day today removing the old racing buckets and then seeing what it would take to install the CJ5 buckets. Put about 5" of wood under the frames and it's close, but needs another inch or so in back, and probably 2" in front to get the correct seat angle.
Once I had things close I cut a bunch of 1.75" box tubing I had in the scrap bin, and tacked it together. Drilled the mounting pattern and bolted them to the seats for a tet fit prior to final welding. The bases are wider than the old ones, and sit too close to the tunnel, so had to make the base on the tunnel side of the floor offset in 1.5" to clear the tunnel. Refitted them with the offset and they looked good to go. Did a test sitting, and they feel right for height, so went ahead and welded them up.
Tomorrow I'll finish painting the frames and then drill new mounting holes. My radio was under the old seats in an aluminum plate I fabbed, so still need to figure how to mount it again under the new seats.
Comment
-
Got the frames installed and bolted the new seats in. Relocated the lap belts and shoulder harnesses, which work much better with the new seats and frames. 2" of snow today, so no trips around the block to see how the seats feel, but a trial in the garage tells me they'll be much more comfortable!
Last edited by 1946Austin; March 14, 2012, 07:42 AM.
Comment
-
Originally posted by mlcraven View PostGreat video! But let's just say...not the least bit stealthyLast edited by 1946Austin; March 14, 2012, 07:44 AM.
Comment
-
Originally posted by Beagle View PostThere's something primal about a brutally effective uncompromised machine. Sure, it's subtle, like a 12 pound sledge hammer.
Comment
-
Originally posted by 1946Austin View PostExactly! That's kinda the point of a street legal gasser. Something that looks and sounds like it shouldn't even be on the street.
Comment
-
Originally posted by Thumpin455 View PostThat can be achieved without a straight axle, but man does the gasser look drive home the point. Who wants quiet in a car like that anyway? Its not a freakin Taxi.
Comment
-
Weather was horrible again today; snow, hail, you name it. Decided to install the new fuel block and hard lines on the Austin. The fuel block is one I got from friend called "RICHIES Scoops" He has these cast up and they're really a nice old school touch for any hotrod.
The old lines I had were all rubber hose with clamps and a dual feed line I chopped up to make it fit my canted carb tunnel ram system. Here's what it used to look like:
And here it is with hard lines bent up and the new RICHIES buel block:
Last edited by 1946Austin; March 18, 2012, 04:04 PM.
Comment
-
Originally posted by SuperBuickGuy View PostVery nice. I know about that snow and rain, I got to wrench in it - my truck decided to be persnickity and I had to readjust a hose clamp on the cooling system.... not perfect, but I made it back to Seattle.
Comment
Comment