PDA

View Full Version : Ford COP


CTX-SLPR
May 30th, 2011, 09:51 PM
Hey guys,

Anyone know where I can get new plug ends (just the plastic ends, not a pigtail) for the Ford COP's? I snapped 2 of the clips on my Lincoln's when changing the coils and plugs and am now holding the plugs in with zipties.

Thanks,
Buckeye
May 31st, 2011, 06:38 PM
Napa can order most replacement plugs but you will need to take the coil in with you to match it up
Darren N.
June 1st, 2011, 11:01 AM
If you're after the "boot", Rock Auto should have them for around $4.

http://www.magnecor.com/magnecor1/images/ford-cop-assembly1.jpg
milner351
June 1st, 2011, 11:51 AM
I'm not the best with our parts system - I had one of the guys in the garage look it up - and he can't come up with separate part number listings - just the whole coil assembly.
CTX-SLPR
June 1st, 2011, 07:25 PM
The boots are fine, the coils themselves are brand new but the clips on the harness broke the internal catches so I had to zip tie them on. I need the new plastic plugs or a pigtail that I can pull apart and get the connectors off of. The wiring is fine, just the plastic catches are broken.
min301
June 1st, 2011, 07:39 PM
Contact your local Car Quest, if they don't have em,
they can certainly work with the dealers and get them for you.

That's who I've gotten them through.
Stich496
June 1st, 2011, 07:52 PM
junk yards are full of them..
min301
June 1st, 2011, 07:55 PM
junk yards are full of them..

Ready to break...just like his.
CTX-SLPR
June 1st, 2011, 08:28 PM
Ready to break...just like his.Thanks for smacking him down like a professional!

thanks for the tip on CarQuest, loved the one in my hometown in TX. Hopefully the guys here are the same.
Stich496
June 1st, 2011, 09:00 PM
Thanks for smacking him down like a professional!

thanks for the tip on CarQuest, loved the one in my hometown in TX. Hopefully the guys here are the same.

well, if you're not a bull in a china shop. they come out fine, and the price is right..
a few sec. blast from a plumbers torch and they don't break..
mr ford , min should know this..
min301
June 2nd, 2011, 05:39 PM
well, if you're not a bull in a china shop. they come out fine, and the price is right..
a few sec. blast from a plumbers torch and they don't break..
mr ford , min should know this..

Actually, they crumble all the time,
did when I was in the Ford shop,
they crumble on many techs all over the place.

Best to replace them with new.
Stich496
June 3rd, 2011, 08:04 AM
Actually, they crumble all the time,
did when I was in the Ford shop,
they crumble on many techs all over the place.

Best to replace them with new.
yes best, but I'm a cheap sob so when I go to the j/y I grab 8, came in handy on the 99 4.6
SpiderGearsMan
June 8th, 2011, 11:47 AM
UMM dealer ???
ls7gto
August 3rd, 2011, 04:58 PM
I have never broke a coil one , normally the injector clip breaks. but I can get the ford part number for you if you still need it.
min301
August 3rd, 2011, 07:33 PM
He's talking about the pigtail connector.
ls7gto
August 4th, 2011, 10:17 AM
I know what the F he is talking about, I WORK AT A F_ING FORD DEALER AND I CAN GIVE HIM THE PART NUMBER IF HE STILL NEEDS IT FOR THE PIG TAIL .
The tab (clip ) in the injector pigtail is the one that normally breaks. We use wire ties to secure them.
min301
August 4th, 2011, 06:04 PM
I know what the F he is talking about, I WORK AT A F_ING FORD DEALER AND I CAN GIVE HIM THE PART NUMBER IF HE STILL NEEDS IT FOR THE PIG TAIL .
The tab (clip ) in the injector pigtail is the one that normally breaks. We use wire ties to secure them.

Me too...btw, take a Midol, your gonna pop a gasket.
I too have worked at Ford dealers, in the service dept.,
I wish I had stayed...
ls7gto
August 4th, 2011, 06:50 PM
bah blah blah.
min301
August 4th, 2011, 08:10 PM
bah blah blah.

And I raise you with a blah...lol, I'm goin to bed, goodnight, bro.